No products
Scalar S 3D printer (20x20x20 cm)
The Scalar S, has a print volume of 20 x 20 x 20 cm. Strong mechanic Modular chassis Strong and reliable motors Cost efficient Free 3D models for upgrades Performant heatbed
333,33 €Shipping within 2/4 daysScalar L 3D printer (30x30x30 cm)
The Scalar L, has a print volume of 300 x 300 x 300. Strong mechanic Modular chassis Strong and reliable motors Cost efficient Free 3D models for upgrades Efficient heat bed
666,66 €Shipping within 2/4 daysScalar XL Premium 3D printer kit, 40x30x30cm
1 Review(s)Strong mechanic Modular chassis Strong and reliable motors Cost efficient Free 3D models for upgrades Increased Safety Performant heatbed
833,33 €3Dtox the 3D printer air purifier
Easy to install compatible with most FDM 3D printers Pre-assembled kit, ready to work within 10 minutes
141,25 €In Stock[S] Enclosure with air filtration system...
Modular enclosure for 3D Scalar S 3D printer The enclosure is installed over the existing chassis Transparent acrylic doors doubles front doors with magnet stoppers Integrated air filtration Only compatible with Scalar S 20x20x20 print volume
207,50 €In StockDimafix Pen - Dabber format
Dimafix Pen (90ml) is a new product based on Dimafix formula. Maintains the same adhesion properties of Dimafix spray format but in dabber liquid format. More than 100 uses Easy to clean Soluble in water Does not contain any gaz
10,75 €In StockDimafix Spray - the ultimate lac for 3d...
Dimafix is a spray tailored for 3D printers with FFF technology and Heated Bed. No warping even in large ABS parts. You will be able to print in all kind of thermoplastic materials. While the bed is hot the adhesive effect will be working even in large prints. When the Heated Bed’s temperature goes down the adhesion effect disappears and the model...
12,42 €In Stock
![[S] Enclosure with air filtration system for Scalar S](http://3dmodularsystems.com/2699-home_default/-s-enclosure-with-air-filtration-system-for-scalar-s.jpg "[S] Enclosure with air filtration system for Scalar S")
1.5m Serial link cable RS232 DB9 male-male...
Cable for RS232 serial link DB9 Male-Male Compatible with 3Dtox V2 Length: 1.5M Cross cable
1,70 €In StockDelta fan THA0412BN 12V 19000RPM 10.68W
Fan for 3Dtox V2 12V 19 000 rpm 29.52 CFM 10.68W 0.89A 40x40x28mm Ball bearing
20,00 €In StockTransparent PVC tube for 3Dtox V2
PVC transparent tube Length: 1m Inner diameter : 13mm Outer diameter: 17mm Thickness: 2 mm Compatible with 3Dtox and 3Dtox V2 Temperature range: -20°C à +60°C
6,58 €In StockRed rubber tube for 3Dtox V2
Rubber tube Length: 1m Inner diameter : 12mm Outer diameter: 17mm Thickness: 2.5mm Compatible with 3Dtox and 3Dtox V2
8,25 €In StockPMS 1003 - Air quality sensor module PM1...
PMS 1003 Air Quality sensor module Measure range: 0.3-1.0 | 1.0-2.5 | 2.5-10 um Measure accuracy : 50% 0.3um, 98% 0.5um Single response time: <=1s Input power supply voltage: 5V working current: 120mA Working temperature range: -10°C - 60°C Dimentions: 65x42x23mm
28,00 €In StockRocker switch KCD11-101 12V 3A
Rocker Switch KCD11-101250V AC - 3A125V AC - 5A2 contactsLifespan: 10 000Contact resistancet: <0.3 Ω
0,50 €In Stockrs232 to TTL Arduino transceiver
RS232 communication transceiver for Arduino, esp 32 , raspberry pi Compatible with Arduino, raspberry pi, esp32 Chip: MAX3232 Input voltage range: 3.3-5V Interface VCC, RX, Tx, GND Data speed: Jusqu'à 250 Kbits/s Low power: 300 uA Dimentions: 31.5 x 34 x 15.7 mm
0,92 €In Stock
Full aluminium plate kit (3mm thick) 33x30cm
Pack of 2 aluminum plates 3mm thick Laser cut 1 top plate (print surface) 330x300x3mm with 4 holes in the corners for screws1 bottom plate 330x300x3mm with 4 holes in the corners for screws 10 holes for bearing and belt supports
39,33 € 49,17 € -20%Reduced price!In StockTop aluminium plate for Scalar L 3D...
1 aluminum plates 3mm thick Laser cut 1 top plate 330x300x3mm with 4 holes in the corners for screws
25,27 € 31,58 € -20%Reduced price!In StockBullDog Extruder for 1.75mm filament
Full metal Bulldog Extruder for 1.75mm reprap 3D printers Full aluminium metal body Very strong grip Compatible with Nema 17 stepper motor for 1.75mm filament Stepper motor not included
23,00 € 30,00 €Reduced price!In StockBottom aluminium plate for Scalar L 3D...
1 aluminum plates 2mm thick Laser cut 1 top plate 320x320x2mm with 4 holes in the corners for screws 4 central holes for holding system
16,67 € 20,83 € -20%Reduced price!In Stock
Follow us on Facebook
Livraison
Livraison via colissimo ou en point relais.
Service Client
06.17.48.38.76 / 06.07.87.83.89
Du lundi au vendredi de 10h à 12h et de 14h à 19hModes de paiment
Carte bleue, Paypal, Virement
Le concept
Imprimantes 3D évolutives
Nos imprimantes ont été pensées dans le but d’être améliorées et complétées en fonction de vos envies/besoins.
Nul besoin de racheter une imprimante dans 6 mois lorsque la technologie évoluera :-)
Il suffira de nous acheter un kit d’évolution !