No products
New products
-
MKS-SGen 32Bits Controler board for 3d printer
MKS SGEN 3D printer 32bits controler board LPC1769 Cortex-M3 32bits...
48,03 € -
MKS-SGen_L 32Bits Controler board for 3d printer
MKS SGEN L 3D printer 32bits controler board LPC1769 Cortex-M3 32bits...
23,75 € -
0.4mm Brass Nozzle for 1.75mm hot end CR-X
Hot end nozzle of 3D printers: Threading: M6 Nozzle diameter: 0.4mm...
5,00 € -
TMC2209 Silent Stepper motor driver
Stepper Motor Driver based on a Trinamic TMC2209 with soldered pin headers
10,52 € -
-
-
-
608 Hybrid Ceramic bearing for hand spinner
2,83 € 3,33 €
Stepper motor drivers There are 14 products.
A4988 StepStick motor driver
This pololu A4988 stepper motor driver is installed in a very largme amount of DIY 3D printers. It can be considered as the reference stepper driver amount stepper drivers. Courant dmaximum de bobine: 1.75A Max avec dissipateur. Max Current per coil: 1.75A
3,10 €In StockDRV8825 Stepper motor driver
Allows to drive Stepper motors. Max coil current: 2.2A More powerfull and more precise than the commonly used A4988 Needs a good air flow below the chip THe heatsink is optional if you have a good air flow, but needed in order to use the max current. Maximum resultion of 1/32 micro-steps supported by 8bit micro-controlers such as Atmega 2560.
3,35 €In StockDRV8825/A4988 Stepper motor driver control...
Expansion board for Stepper Drivers Compatible with : DRV8825, A4988, TMC2208, LV8927, TBS109, TMC2100 Switch for micro stepping configuration power supply pins : +5V / +12V /+24V Control pins: Enable, Direction, Step Compatible with Arduino, Raspberry Pi, Ramps 1.4, ARM, etc....
4,10 €Out of stockTL-Smoother for DRV8825 stepper motor
TL-Smoother, specially designed to smooth out and rectify the signal from 3D printer stepper motor drivers. Specially designed for DRV8825 Also compatible with other stepper motor drivers such as A4988, etc...
5,00 €In StockMKS LV8729 - ultra quiet stepper motor...
Ultra quiet stepper motor Drivers LV8729 High Qaality Compatible and replaces the well known A4988 and DRV8825 stepper motor drivers More silent and smooth than a A4988 Can reach up to 1/128th micro stepings Compatible with most standard controler boards Ideal for 3D printers, CNC, laser cutters, Hot wire machines
6,68 €In StockTMC2208 Silent Stepper motor driver
Stepper Motor Driver based on a Trinamic TMC2208 with soldered pin headers
7,68 €In StockTMC2100 Silent Stepper motor driver
Stepper Motor Driver based on a Trinamic TMC2100 with soldered pin headers
11,67 €In StockTMC2130 Silent stepper motor driver
Stepper Motor Driver based on a Trinamic TMC2130 with soldered pin headers Controls pins soldered upward
11,35 €In Stock2 ways SPI control wire for TMC2130
SPI Cable for 2 stepper drivers TMC2130 Compatible with the following boards Ramps 1.4 MKS Gen 1.4 MKS GEN LAllows to access advanced drivers functionalitiesstealthChop spreadCycle coolStep stallguard dcStep-load
1,50 €In StockMKS Tl-Smoother (Stepstick Protector)...
MKS TL-Smoother Allows to smooth out the current on your Nema stepper motors and reduces electric noise and mechanical vibrations Enhance the quality of your prints To be installed below your existing stepper motor drivers Compatible with DRV8825, TMC2100, TMC2130, TMC2208 etc...
2,33 €In StockMKS CD expansion board for high current...
Expansion board for independant stepper motor drivers (57/86 stepper drives) Built in buffer chip (type 74HC04) Ideal to connect your MCU to any high current stepper motor drives This module is compatible with standard A4988, DRV8825 etc... stepper motor drivers pinout
5,02 €In StockTBS109 - ultra quiet stepper and powerfull...
Ultra and powerful stepper motor Drivers TBS109 High Quality Max 4A 50V Advanced dynamic hybrid attenuation (ADMD) More silent and powerful than a A4988 and Drv8825 Can reach up to 1/32th micro stepings Compatible with most standard controller boards Ideal for 3D printers, CNC, laser cutters, Hot wire machines
8,77 €Out of stock
