No products
New products
-
0.8mm Ruby Nozzle for 1.75mm hot end
Hot end nozzle of 3D printers: Threading: M6 Nozzle diameter: 0.8mm...
66,67 € -
0.4mm Ruby Nozzle for 1.75mm hot end
Hot end nozzle of 3D printers: Threading: M6 Nozzle diameter: 0.4mm...
66,67 € -
Silent Stepper motor driver MKS TB67S109 3.32A
Silent stepper motor driver TB67S109 Chipset Toshiba TB67S109 Max...
6,50 € -
MP1584EN DC-DC Step Down converter 4.5-28Vdc to 0.8-20Vdc 3A
Ultra small DC-DC converter MP1584EN Input : 4.5-28Vdc Output:...
2,18 € -
24V 50W 1m Heater cartridge for Hot ends
Default 50W 24V Heater cartridge for RepRap HotEnds Will boost the...
4,00 € -
12V 50W 1m Heater cartridge for Hot ends
Default 50W 12V Heater cartridge for RepRap HotEnds Will boost the...
4,00 €
-
Top aluminium plate for Scalar L 3D printer 330x300x3mm
1 aluminum plates 3mm thick Laser...
25,27 € -20% 31,58 €
30% There are 15 products.
TFT 2.8" Touch screen for 3D printer
TFT 2.8" Touch screen compatible with Ramps 1.4 and MKS BASE Touch Screen SD card support USB key support Can be connected to a backup UPS Allows to resume print from power shortage Allows filament change during print
49,17 €In StockMKS CD expansion board for high current...
Expansion board for independant stepper motor drivers (57/86 stepper drives) Built in buffer chip (type 74HC04) Ideal to connect your MCU to any high current stepper motor drives This module is compatible with standard A4988, DRV8825 etc... stepper motor drivers pinout
5,02 €In StockTMC2208 Silent Stepper motor driver
Stepper Motor Driver based on a Trinamic TMC2208 with soldered pin headers
7,68 €In StockTMC2130 Silent stepper motor driver
Stepper Motor Driver based on a Trinamic TMC2130 with soldered pin headers Controls pins soldered upward
11,35 €In Stock[3500RPM] 60mm 12V fan, 14.3CFM, 20cm
12V 60mm fan, used inside Scalar 3D printers kit.
4,00 €In StockTBS109 - ultra quiet stepper and powerfull...
Ultra and powerful stepper motor Drivers TBS109 High Quality Max 4A 50V Advanced dynamic hybrid attenuation (ADMD) More silent and powerful than a A4988 and Drv8825 Can reach up to 1/32th micro stepings Compatible with most standard controller boards Ideal for 3D printers, CNC, laser cutters, Hot wire machines
8,77 €Out of stock5 Nema 17 Stepper motor for Scalar Family...
This pack contains 5 NEMA17 stepper motors compatible with Scalar 3D printers. Powerful, robust, with a nice capacity to stay cool thanks to it's 40mm high and limited 1.2A per phase; Uses only 1.2A for a 4000 g.cm torque (0.44 Nm ou 62 Oz.In) It contains: 5 motors with 1m lead wires and a 4 pin female dupont connector
65,42 €In StockDRV8825 Stepper motor driver
Allows to drive Stepper motors. Max coil current: 2.2A More powerfull and more precise than the commonly used A4988 Needs a good air flow below the chip THe heatsink is optional if you have a good air flow, but needed in order to use the max current. Maximum resultion of 1/32 micro-steps supported by 8bit micro-controlers such as Atmega 2560.
3,35 €In StockSF-1 060810 Bronze bushing
SF-1 bronze bushing Allow the same usage as standard Linear bearings Auto lubricated Compatible with 6mm smooth rods Quieter than LM6UU linear bearing Extended lifespan
0,75 €In StockAnti wobble top idler for CR-10 Anet E10...
Top idler specially designed to prevent wobbling of the Z lead screws Compatible with Creality CR-10 and Anet E10 3D printers Also compatible with any 3D printers using 8mm lead screws and 2020 extrusion profiles
6,67 €In Stock[135°C] 220V Silicone heater 29x29cm for...
Large silicone heater for RepRap 3D printers, specially adapted for CR-10 3D printers Material: Silicone Size: 290x290mm Power: 600W Input Voltage: 220V Power supply cable length: 1 metre Back Tape: 3M Thermal fuse set at 140°C Dedicated holes for CR10 like heatbed
50,83 €In Stock[CR-10][135°C] 600W 220V heatbed upgrade
2 Review(s)Heat bed upgrade 220V / 600W for CR-10 3d printer can reach 60°C in 1 minute 10 can reach 110°C in less than 3minutes Built-in thermal protection (max 135 °C)
59,17 €In Stock
![[CR-10][135°C] 600W 220V heatbed upgrade](http://3dmodularsystems.com/2241-home_default/-cr-10-600w-220v-heatbed-upgrade.jpg "[CR-10][135°C] 600W 220V heatbed upgrade")