No products
New products
-
Silent Stepper motor driver MKS TB67S109 3.32A
Silent stepper motor driver TB67S109 Chipset Toshiba TB67S109 Max...
6,50 € -
MP1584EN DC-DC Step Down converter 4.5-28Vdc to 0.8-20Vdc 3A
Ultra small DC-DC converter MP1584EN Input : 4.5-28Vdc Output:...
2,18 € -
24V 50W 1m Heater cartridge for Hot ends
Default 50W 24V Heater cartridge for RepRap HotEnds Will boost the...
4,00 € -
12V 50W 1m Heater cartridge for Hot ends
Default 50W 12V Heater cartridge for RepRap HotEnds Will boost the...
4,00 €
-
Bottom aluminium plate for Scalar L 3D printer 320x320x2mm
1 aluminum plates 2mm thick Laser...
16,67 € -20% 20,83 €
3Dtox There are 14 products.
Delta fan THA0412BN 12V 19000RPM 10.68W
Fan for 3Dtox V2 12V 19 000 rpm 29.52 CFM 10.68W 0.89A 40x40x28mm Ball bearing
20,00 €In StockTransparent PVC tube for 3Dtox V2
PVC transparent tube Length: 1m Inner diameter : 13mm Outer diameter: 17mm Thickness: 2 mm Compatible with 3Dtox and 3Dtox V2 Temperature range: -20°C à +60°C
6,58 €In StockRed rubber tube for 3Dtox V2
Rubber tube Length: 1m Inner diameter : 12mm Outer diameter: 17mm Thickness: 2.5mm Compatible with 3Dtox and 3Dtox V2
8,25 €In StockPMS 1003 - Air quality sensor module PM1...
PMS 1003 Air Quality sensor module Measure range: 0.3-1.0 | 1.0-2.5 | 2.5-10 um Measure accuracy : 50% 0.3um, 98% 0.5um Single response time: <=1s Input power supply voltage: 5V working current: 120mA Working temperature range: -10°C - 60°C Dimentions: 65x42x23mm
28,00 €In StockRocker switch KCD11-101 12V 3A
Rocker Switch KCD11-101250V AC - 3A125V AC - 5A2 contactsLifespan: 10 000Contact resistancet: <0.3 Ω
0,50 €In Stockrs232 to TTL Arduino transceiver
RS232 communication transceiver for Arduino, esp 32 , raspberry pi Compatible with Arduino, raspberry pi, esp32 Chip: MAX3232 Input voltage range: 3.3-5V Interface VCC, RX, Tx, GND Data speed: Jusqu'à 250 Kbits/s Low power: 300 uA Dimentions: 31.5 x 34 x 15.7 mm
0,92 €In StockMKS-Gen_L Controler board for 3d printer
1 Review(s)MKS GEN L 3D printer controler board Atmega 2560 microcontroler Integrated Ramps 1.4 board has similar Aux outputs as Ramps 1.4 Compatible with all standard Stepper motor drivers for 3D printers Compact form factor Ideal replacement for Arduino 2560 + Ramps 1.4 Supports 12/24VDC input Optimized MOSFET heat dissipation
20,83 €In StockRepRapDiscount LCD 2004 4x20 caracters for...
This article contains: 1x Smart Adapter for Ramps 1.4 1x 5" LCD controler with SD card slot 2x 60cm long cables fprovided with push button cap
12,08 €In StockDC-022 2.1x5.5mm DC Power panel jack...
Quantity: 1 piece Compatible with Jack DC plugs 2.1mm x 5.5mm x 9mm Length: 17mm 12V 2A Max Required hole: 12mm Provided with the fixation nut Exposed part: 2mm high,14mm diameter 20mm deep is required behind the pannel model: DC-022
0,50 €In Stock2x 3M Gaz filter ABEK1P3
Gaz cartridge of type ABEK1P3 contains: 2 ABEK1 cartridge- 3M 6059 2 particules filters P3 - 3M 5925 2 plastic covers for particules filters - 3M 501 Allows to filter most of gaz and particules generated by ABS
15,83 €In StockUltra microSD 8GB UHS-I Card 48MB/s
Capacity: 8 GB Read Speed: up to 48MB/S Video Speed: C10 Form Factor: microSDHC
4,58 €In Stock
