No products
New products
-
Makerbase MKS SERVO42 closed loop motor
Moteur à boucle fermé avec encodeur magnétique Simple à installer...
39,92 € -
Makerbase MKS Hotbed MOS V1.1 +30A
MOSFET from Makerbase Built-in power MOSFET that can support a load of...
14,08 €
-
Full aluminium plate kit (3mm thick) 33x30cm
Pack of 2 aluminum plates 3mm thick...
39,33 € -20% 49,17 €
Misc There are 36 products.
set of 100 Rilsan/Colson cable tie 2.5x100mm
Nylon white cable ties (Rilsan/Colson) Quantity: 100 pcs Width 2.5mm Length: 100mm
2,50 €In StockRocker switch 3 positons 6 pins 10A
Rocker switch 3 positions ON-OFF-ON 250V AC 6A 125V AC 10A 6 Pins 3 Positions
2,08 €Out of stockCD-20 Ceramic screw diver 1.8x0.4mm
Ceramic screw diver. Great tool to adjust various kind of electronic device sensitive to Electro static dischanges such as Steper motor drivers. Model: CD-20 Type: Flat screw diver Width: 1.8mm Diameter: 0.4mm Ideal for 3D printer stepper drivers Warning: Can break easily
1,75 €In StockPolyimide/Kapton Tape 50mm 33 meters
Polyimid/Kapton tape ideal for 3D printing surface with heat bed. Heat resistant: 280°C Simple side tape Tape Width: 50mm Tape length: 33Meters(100 feet)
9,08 €In StockFiltre anti poussière pour ventilateur de...
This dust filter is an easy, economic and easy to maintain solution to filter big and average dust particules that will stick on your equipments or electronic boards. Can easily be fixed on the input of any 80mm fan. The dust will stick on the filter grid by it's own. A small paper sheet can be used to clean the filter once in while.
0,83 €In StockTwinWire 24 AWG Red and black, sold by...
Twin Wire 24 AWG (diametre 0.5106mm, area 0.2047mm²) 2 wires (red and black) Sold by linear meter Used to increase fan lead wires or to wire 3D printers end stops.. Can be used on any application requirering less than 500mA current
1,00 €In StockMicro switch, end stop with roller for 3D...
Perfect end stop for 3D printers type: SS-5GL2 Max Curent: 5A 125VAC or 3A 250VAC 3 pins (C, NO, NC) Roller: oui Size: 19.5x5,5x25mm Screw holes: 2.5mm
0,83 €In Stock1/8" BSPT push to fit connector for 6mm...
Push to fit pneumatic straight connector for bowden type PTFE tubes. Compatible with 6mm tubes for 3mm filaments. Thread: 1/8 " BSPT Thread type: NPTF conical Quick connector Can handle up to 10 bars of pressure material: Acetal Certifications: FDA and NSF
2,50 €In Stock1/8" BSPT brass push to fit connector for...
Push to fit pneumatic straight connector for bowden type PTFE tubes. Compatible with 6mm tubes for 3mm filaments. Thread: 1/8 " BSPT Quick connector Can handle up to 10 bars of pressure material: Plastic + brass
1,00 €In Stock1/8" BSPT brass push to fit connector for...
Push to fit pneumatic straight connector for bowden type PTFE tubes. Compatible with 4mm OD tubes for 1.75mm filaments. Thread: 1/8 " BSPT Quick connector Can handle up to 10 bars of pressure material: Plastic + brass
1,67 €In Stock4 Pcs of 51mm Bulldog paper clip
Bulldog type paper clips of 51mm long for 25 mm max spacing Ideal to keep your heatbed and print surface togather. (glass, aluminum etc..). Length: 51mm Width: 30mm Spacing: 25mm Arm length: 60mm
2,50 €Out of stock4 Pcs of 32mm Bulldog paper clip
Bulldog type paper clips of 32mm long for 13 mm max spacing Ideal to keep your heatbed and print surface together. (glass, aluminum etc..). Length: 32mm Width: 19mm Spacing: 13mm Arm length: 37mm
2,00 €Out of stock
