No products
Prices are tax included
New products
-
RRD Fan extender for dual extrusion
Required if using the power fan output to drive the 2nd hot end heater....
6,00 € -
![[S] Dual extrusion upgrade Chimera Plus for Scalar S](http://3dmodularsystems.com/2722-small_default/-s-dual-extrusion-upgrade-chimera-plus-for-scalar-s.jpg)
[S] Dual extrusion upgrade Chimera Plus for Scalar S
Dual extrusion upgrade kit Two inputs, two outputs. The classic...
149,90 € -
![[S] Enclosure with air filtration system for Scalar S](http://3dmodularsystems.com/2699-small_default/-s-enclosure-with-air-filtration-system-for-scalar-s.jpg)
[S] Enclosure with air filtration system for Scalar S
Modular enclosure for 3D Scalar S 3D printer The enclosure is installed...
249,00 € -
![[XLP] Enclosure with air filtration system for Scalar XL Premium](http://3dmodularsystems.com/2627-small_default/-xlp-enclosure-with-air-filtration-system-for-scalar-xl-premium.jpg)
[XLP] Enclosure with air filtration system for Scalar XL Premium
Modular enclosure for 3D Scalar XL premium 3D printer The enclosure is...
349,00 € -
chainable RGB led WS2812
Programmable and chainable RGBW LED module (same model used on Neopixel)...
1,20 € -
PLA Electronic box for MKS GEN 1.4 / MKS GEN L
PLA electronic enclosure for MKS GEN 1.4 / MKS GEN-L boards The...
25,00 €
Eletronic boards
Eletronic boards There are 17 products.
CD-20 Ceramic screw diver 1.8x0.4mm
Ceramic screw diver. Great tool to adjust various kind of electronic device sensitive to Electro static dischanges such as Steper motor drivers. Model: CD-20 Type: Flat screw diver Width: 1.8mm Diameter: 0.4mm Ideal for 3D printer stepper drivers Warning: Can break easily
2,10 €In StockArduino Mega 2560 r3
Arduino Mega 2560 r3 controler board Microcontroleur Atmega 2560 Flash Memory: 256K SRAM: 8K EEPROM: 4K Frequency: 16 Mhz
17,53 €In StockShield Ramps 1.4 for Arduino Mega 2560
arduino Mega 2560 Shield Daughter board compatible with Arduino Mega 2560 Often used to drive 3D Printers Input voltage 12V Can drive the following axes X, Y Z and 2 extruders Support up to 3 thermistors Allow the use of up to 4 servo motors
9,93 €In StockGaz detector kit for Scalar 3D printer
Smoke detector module for RepRap 3D printers and Scalar Compatible with RepRap 3D printers Can be directly connected on 1 pin of your electronics (can be adjusted from the firmware) Compatible with marlin firmware Detects: Smoke, Hydrogen, alcohol, methane, propane, i-buane, LPG
7,20 €Out of stockRepRapDiscount LCD 2004 4x20 caracters for...
This article contains: 1x Smart Adapter for Ramps 1.4 1x 5" LCD controler with SD card slot 2x 60cm long cables fprovided with push button cap
16,90 €In StockRaspberry Pi 3 Kit for 3D printer
Control your 3D printer remotely with this kit.Your printer becomes accessible via wifi, but also outside the home.You can follow the printing with a webcam, start or stop a print from a distance!
75,00 €In stockTFT 2.8" Touch screen for 3D printer
TFT 2.8" Touch screen compatible with Ramps 1.4 and MKS BASE Touch Screen SD card support USB key support Can be connected to a backup UPS Allows to resume print from power shortage Allows filament change during print
75,10 €In Stock32Bits 100Mhz Re-Arm Controler for Scalar...
RE-ARM is a 100Mhz, 32-bit ARM controller with the popular Arduino MEGA footprint. It's a plug-in replacement for the Arduino Mega in your RAMPS setup for a quick and easy upgrade to 32-bit goodness. It runs the awesome Smoothieware firmware by Arthur Wolf.
75,10 €In Stock32Bits 100Mhz Re-Arm Controler + GLCD Full...
RE-ARM is a 100Mhz, 32-bit ARM controller with the popular Arduino MEGA footprint. It's a plug-in replacement for the Arduino Mega in your RAMPS setup for a quick and easy upgrade to 32-bit goodness. It runs the awesome Smoothieware firmware by Arthur Wolf.
95,20 €In StockDRV8825/A4988 Stepper motor driver control...
Expansion board for Stepper Drivers Compatible with : DRV8825, A4988 Switch for micro stepping configuration power supply pins : +5V / +12V /+24V Control pins: Enable, Direction, Step Compatible with Arduino, Raspberry Pi, Ramps 1.4, ARM, etc....
4,92 €In StockTL-Smoother for DRV8825 stepper motor
TL-Smoother, specially designed to smooth out and rectify the signal from 3D printer stepper motor drivers. Specially designed for DRV8825 Also compatible with other stepper motor drivers such as A4988, etc...
7,20 €In Stock[CR-10] MOSFET MKS MOS25 for 3D printer 12...
MOSFET for 3D printers 12V / 24VDC heat beds Input voltage: 12/24VDC Max Currrent: 25A Max heat bed power: 200/250W You need to cool down the heatsink of the MOSFET before use Compatible with reprap, Creality CR-10, Anet E10, etc... model: MKS MOS25
9,50 €In Stock
![[CR-10] MOSFET MOS25 for 3D printer 12 / 24V Heat beds](http://3dmodularsystems.com/2326-home_default/-cr-10-mosfet-for-3d-printer-12-24v-heat-beds.jpg "[CR-10] MOSFET MOS25 for 3D printer 12 / 24V Heat beds")