No products
Prices are tax included
-
128X64 OLED Display module for Arduino 0.96" I2C, IIC
0.96" OLED display for Arduino...
2,60 € -60% 6,50 €
heatbeds for DIY reprap 3D printers
Heat Bed There are 12 products.
Thermistor 100K, 3950 1%, 1 meter lead...
Thermistor 100K for 3D printer heatbeds Beta: 3950 1% Resistor: 100K Max temperature: 285°C Compatible with marlin firmware (table #11) 1 meter lead wire wired with 2 pin dupont connector
0,46 € 1,53 € -70%Reduced price!In StockPack heatbed for Scalar XL 3D printer...
Heatbed Pack for Scalar XL 3D printer Contains 2 aluminum plates (3mm thick) laser cut with fixation holes 1 silicone heatter (700w-220V) 1 thermistor 1 static relay Free 1 set of nuts and bolts: 4 spacers 4 conic head screws 4 nuts for conic screws 10 M6x12mm screws 20 M3 washers 10 nylstop nuts
104,99 € 149,99 € -30%Reduced price!Out of stockFull aluminium plate kit (3mm thick) 33x30cm
Pack of 2 aluminum plates 3mm thick Laser cut 1 top plate (print surface) 330x300x3mm with 4 holes in the corners for screws1 bottom plate 330x300x2mm with 4 holes in the corners for screws 10 holes for bearing and belt supports
29,50 € 59,00 € -50%Reduced price!In StockPack heatbed for Scalar L 3D printer...
Heatbed Pack for Scalar L 3D printer Contains: 2 aluminum plates (3mm thick) laser cut with fixation holes 1 silicone heatter (600w-220V) 1 thermistor 1 static relay Free: 1 set of nuts and bolts: 4 spacers 4 conic head screws 4 nuts for conic screws 10 M6x12mm screws 20 M3 washers 10 nylstop nuts
134,99 €Out of stockTop aluminium plate for Scalar S 3D...
1 aluminum plates 3mm thick Laser cut 1 top plate 220x220x3mm with 4 holes in the corners for screws
7,02 € 23,40 € -70%Reduced price!In StockBottom aluminium plate for Scalar S 3D...
1 aluminum plates 2mm thick Laser cut 1 top plate 220x220x2mm with 4 holes in the corners for screws 4 central holes for holding system
6,00 € 20,00 € -70%Reduced price!In StockPack heatbed for Scalar S 3D printer...
Heatbed Pack for Scalar S 3D printer Contains: 2 aluminum plates laser cut with fixation holes (1 top plate 3mm thick, 1 bottom plate 2mm thick) 1 silicone heatter (250W-220V) 1 thermistor 1 static relay + Wires Free: 1 set of nuts and bolts: 4 springs 4 conic head screws 4 nuts for conic screws 4 M6x12mm screws 4 M3 washers 4 nylstop nuts
68,95 € 98,50 € -30%Reduced price!Out of stockThermistor 100K, 3950 1%, 1.5 meters lead...
Thermistor 100K for 3D printer heatbeds Beta: 3950 1% Resistor: 100K Max temperature: 285°C Compatible with marlin firmware (table #11) 1.5 meters lead wire wired with 2 pin dupont connector
0,91 € 3,03 € -70%Reduced price!In StockBottom aluminium plate for Scalar L 3D...
1 aluminum plates 2mm thick Laser cut 1 top plate 320x320x2mm with 4 holes in the corners for screws 4 central holes for holding system
12,50 € 25,00 € -50%Reduced price!In Stock[95°C] 220V Heatbed 19x19cm (Scalar S) -...
Large silicone heater for RepRap 3D printers MAX 95°C (Thermal fuse set at 100°C) Material: Silicone Size: 190x190mm Power: 250W Input Voltage: 220V Power supply cable length: 1 metre Back Tape: 3M
14,50 € 29,00 € -50%Reduced price!In Stock[CR-10] MOSFET MKS MOS25 for 3D printer 12...
MOSFET for 3D printers 12V / 24VDC heat beds Input voltage: 12/24VDC Max Currrent: 25A Max heat bed power: 200/250W You need to cool down the heatsink of the MOSFET before use Compatible with reprap, Creality CR-10, Anet E10, etc... model: MKS MOS25
7,60 € 9,50 € -20%Reduced price!In Stock[95°C] Silicone heater 600W 220V 29x29cm...
Large silicone heater for RepRap 3D printers Material: Silicone Size: 290x290mm Power: 600W Input Voltage: 220V can reach 60°C in 1 minute 10 can reach 110°C in less than 3minutes Power supply cable length: 1 metre Back Tape: 3M Thermal fuse set at 100°C
61,00 €In Stock
![[95°C] Silicone heater 250W 220V 190x190mm](http://3dmodularsystems.com/2301-home_default/-95c-silicone-heater-250w-220v-190x190mm-for-scalar-s.jpg "[95°C] Silicone heater 250W 220V 190x190mm")
![[CR-10] MOSFET MOS25 for 3D printer 12 / 24V Heat beds](http://3dmodularsystems.com/2326-home_default/-cr-10-mosfet-for-3d-printer-12-24v-heat-beds.jpg "[CR-10] MOSFET MOS25 for 3D printer 12 / 24V Heat beds")
![[95°C] Silicone heater 600W 220V 29x29cm](http://3dmodularsystems.com/2730-home_default/-95c-silicone-heater-600w-220v-29x29cm-for-scalar-l.jpg "[95°C] Silicone heater 600W 220V 29x29cm")