Shipping within 2/4 days
Warning: Last items in stock!
|Stepper drivers resolution||16 micro steps|
|Print size (lxWxH)||40cm x 30cm x 35 cm|
|Stepper drivers||5X A4988|
|Printer size (lxWxH)||80cm x 47cm x 60cm|
|Operating temperature||10-30°C (50 - 86°F)|
|Layer thickness||from 50 microns up to 1/2 nozzle size|
|Heat Bed support||Yes|
|Print surface material||3mm Aluminum|
|Heat Bed safety thermal fuse||Yes, calibrated to 140°C (284°F)|
|Heat bed insulation||Yes|
|Heat bed power supply voltage||220V AC|
|HeatBed heat time PLA 25°C-60°C (77°F-140°F)||1 minute|
|HeatBed heat time PLA 25°C-110°C (77°F-230°F)||3 minutes|
|Recommended nozzle size||0.4mm|
|Supported plastic types||PLA, ABS, flexibles filament, wood, laybrick, fluorescent, etc....|
|Supported Filament diameter||1.75mm or 2.85/3mm|
|Auto bed Leveling||Yes - by Inductive probe|
|Thermal Runaway safety||Yes - Handled by firmware|
|Virtual end stops||Yes - MAX End stops are virtual|
|Chassis structure||30x30mm aluminum extrusion|
|SD card reader||Yes - Integrated to the LCD display|
|LCD display||Yes - 20x4 characters|
|CPU type||Atmega 2560 - r3, 16Mhz, 8-Bit , 256 Kbytes program memory, 4KBytes EEPROM memory, 8KBytes SRAM|
|Motor resolution||1.8° / step|
|Motors dimensions (L, W, H)||Nema 17|
Scalar's 3D printers are shipped including 1Kg of (PLA) 1.75 or 3mm depending on the hotend you choose (Tennis ball system not included)
We will provide certain screws and bearing already mounted on the plastic parts. The electronic is already programmed and the hot end is already assembled.
Then have a great time assembling your printer using our online documentation
Contact us if you have any issues regarding your kit ==> firstname.lastname@example.org
You select chat model you want depending on your usage.
1.75mm hot ends are :
Hot ends for 3mm filaments are :
All the Scalar 3D printer are equipped with Auto ed leveling sensors (Inductive probe)
This sensor will probe the proximity of the heat bed using up to 9 points before each print.
This will allow to compensate any heat bed deformation or miss alignments.
The heat bed is made using 2 aluminum plates of about 3mm thick.Springs are provided for you to adjust each corner height as you please.
A dual belt synchronization system is provided in order to get more stability from your heat bed.
The 700W, 220V Heat bed ( with EU power plug => this one can be changed), allows to reach 60°C in less than 60 seconds and 110°C in less than 3 minutes)
Check out the study we made on the Scalar XL on our blog
The machine is provided with 1 single blower fan at the front of the machine. The 2nd blower fan allows a better cooling of your plastic part being printed. (very useful for PLA)
Every parts of the printer is available on our thingiverse page.
The firmware is a generic version of Marlin, It's pre-loaded inside the printer controller.
It is highly recommended to equip your printer with a hood for capturing micro particles created during printing, and an air exhaust system outwards.
If it is not the case, it is advisable to place the printer in a room where you do not stay when printing.
It is imperative to ventilate the room, at least after each print to recycle the air.
We strongly recommend the PLA, a biodegradable plastic and 10x less dangerous than the ABS, which potentially release toxic gases such as carbon monoxide and hydrogen cyanide when printing.
3D Modular Systems Filament PLA 1.75mm 750gr -...
Inductive probe for 3D printer Input voltage:...
ADWIRE Filament PLA 3mm 1kg - Red
E3D-V6 Volcano upgrade kit for E3DV6 3mm hotend
Hot end nozzle of 3D printers: Threading: M6...
Ceramic screw diver. Great tool to adjust...
Polyimid/Kapton tape ideal for 3D printing...
ADWIRE Filament PLA 1.75mm 1kg - Red
Parts for automatic power off of your reprap 3D...