In stock - Shipping 2-4 days
Warning: Last items in stock!
Our 3D printers are kits sold "pre assembled".
This means that we install all the bearings, most of the screws, plug and play PSU, electronic is already programmes and the hot end already assembled.
We provide an E3D V6 hotend. One of the most famous hotend. Mounted with a 0.4mm nozzle.
E3D provides a large choice of nozzle with different diameter and different material that allow you to print every possible filament.
Contact us at firstname.lastname@example.org if you want us to customize the LCD welcome message for you with your pneudo or whatever you want (13 caracters)
1Kg of 3mm plastic is provided in the kit
The firmware and the update procedure is available here:
All our 3D models can be downloaded freely online.
You can visit the dedicated page here : 3D models for Scalar 3D printer
It is highly recommended to equip your printer with a hood for capturing micro particles created during printing, and an air exhaust system outwards.
If it is not the case, it is advisable to place the printer in a room where you do not stay when printing.
It is imperative to ventilate the room, at least after each print to recycle the air.
We strongly recommend the PLA, a biodegradable plastic and 10x less dangerous than the ABS, which potentially release toxic gases such as carbon monoxide and hydrogen cyanide when printing.
|Stepper drivers resolution||16 micro steps|
|Print size (lxWxH)||40cm x 40cm x 40cm|
|Stepper drivers||5X A4988|
|Operating temperature||10-30°C (50 - 86°F)|
|Layer thickness||from 50 microns up to 1/2 nozzle size|
|Heat Bed support||Yes|
|Print surface material||3mm Aluminum|
|Heat Bed safety thermal fuse||Yes, calibrated to 140°C (284°F)|
|Heat bed insulation||Yes|
|Heat bed power supply voltage||220V AC|
|HeatBed heat time PLA 25°C-60°C (77°F-140°F)||1 minute|
|HeatBed heat time PLA 25°C-110°C (77°F-230°F)||3 minutes|
|Recommended nozzle size||0.4mm|
|Supported plastic types||PLA, ABS|
|Supported Filament diameter||1.75mm or 2.85/3mm|
|Auto bed Leveling||Yes - by Inductive probe|
|Thermal Runaway safety||Yes - Handled by firmware|
|Virtual end stops||Yes - MAX End stops are virtual|
|Chassis structure||30x30mm aluminum extrusion|
|SD card reader||Yes - Integrated to the LCD display|
|LCD display||Yes - 20x4 characters|
|CPU type||Atmega 2560 - r3, 16Mhz, 8-Bit , 256 Kbytes program memory, 4KBytes EEPROM memory, 8KBytes SRAM|
|Motor resolution||1.8° / step|
|Motors dimensions (L, W, H)||Nema 17|
|Motor weight||0.4 KG / Motor|
|Motor lead wires||4|
|Motors lead wire length||4 x 1m + 1 x 1.2m|
|Pulley types||GT2 2mm 16 teeth|
|Timing belt type||GT2 2mm|
|Mecanical resolution||X, Y Axis: 10 microns; Z Axis : 6.25 microns|
|Compatible slicers||Cura, Slic3r, MatterControl|
|System requirements||Windows 7 SP1, Open GL 2.1 , 2GB Ram|
|Firmware||Opensource Marlin Firmware (https://github.com/MarlinFirmware/Marlin)|
|Model||Scalar XL Premium 40|
No customer reviews for the moment.
Stepper Motor Driver based on a Trinamic...
WhitePTFE tube for 3D printer filament This...
Hot end nozzle of 3D printers: Threading: M6...
This cleaning needle will help you clean up...
Reinforced GT2 belt, 2mm pitch for 6mm width...
Sensor capable of detecting when you are...
Polyimid/Kapton tape ideal for 3D printing...
Upgrade for Scalar XL / M. Requires Dual Drive...
3D Modular Systems Filament PLA 1.75mm 1Kg -...
3D Modular Systems Filament PETG 1.75mm 1Kg -...