This is a kit containing all the parts for the DIY 3Dtox V2 air filtration system for your 3D printer.
It contains all the electronic parts and nuts and bolts needed in order to assemble your air filtration system kit.
Important: This kit doesn't contain any plastic parts that you will need to print yourself! (see below for more information on where to download the files)
Warning: Last items in stock!
This kit is a for 3Dtox V2 air filtration system for your reprap 3D printer.
It contains the following parts:
- LCD display with SD card reader
- Air quality sensor module
- A powerfull fan
- 2 combined professional air filters 3M (ABEK class)
- 2 RS232 transceiver modules
- 1 ON/OFF rocker switch 10A OR 1 ON/OFF rocker switch 3A
- 1 Fuse holder cable
- 1 power jack 2.1x5.5mm connector
- 1 cable DB9-DB9 male-male
- 1 Micro SD card + Sd card adaptor
- 1 meter rubber or PVC tube
- 1 2A power supply adaptor (EU plug)
All Stl files are provided as OpenSOurce material, and can be downloaded freely on Thingiverse:
THe main board will be programmed with the latest firmware to date.
The firmware source code and the compilation procedure can be found on GitHub
A full documentation on how to assemble, configure and use the device is available here:
Gaz cartridge of type ABEK1P3 contains: 2 ABEK1 cartridge- 3M 6059 2 particules filters P3 - 3M 5925 2 plastic covers for particules filters - 3M 501 Allows to filter most of gaz and particules generated by ABS
Quantity: 1 piece Compatible with Jack DC plugs 2.1mm x 5.5mm x 9mm Length: 17mm 12V 2A Max Required hole: 12mm Provided with the fixation nut Exposed part: 2mm high,14mm diameter 20mm deep is required behind the pannel model: DC-022
MKS GEN L 3D printer controler board Atmega 2560 microcontroler Integrated Ramps 1.4 board has similar Aux outputs as Ramps 1.4 Compatible with all standard Stepper motor drivers for 3D printers Compact form factor Ideal replacement for Arduino 2560 + Ramps 1.4 Supports 12/24VDC input Optimized MOSFET heat dissipation
RS232 communication transceiver for Arduino, esp 32 , raspberry pi Compatible with Arduino, raspberry pi, esp32 Chip: MAX3232 Input voltage range: 3.3-5V Interface VCC, RX, Tx, GND Data speed: Jusqu'à 250 Kbits/s Low power: 300 uA Dimentions: 31.5 x 34 x 15.7 mm
PMS 1003 Air Quality sensor module Measure range: 0.3-1.0 | 1.0-2.5 | 2.5-10 um Measure accuracy : 50% 0.3um, 98% 0.5um Single response time: <=1s Input power supply voltage: 5V working current: 120mA Working temperature range: -10°C - 60°C Dimentions: 65x42x23mm
No customer reviews for the moment.
Hot end nozzle of 3D printers: Threading: M6...
Silicone sock for new E3DV6 heater block only...
Sensor capable of detecting when you are...
Insert for M3 screws Sold by unit
S6000-2RS 10*26*8mm Axial ball bearing...
Insert for M6 screws Sold by unit
Insert for M5 screws Sold by unit
Insert for M4 screws Sold by unit
Main caracteristics: 12V, 0.52A Brushless...
Nema 17 cork gasket Vibration dampener Size:...