No products
Prices are tax included
New products
-
RRD Fan extender for dual extrusion
Required if using the power fan output to drive the 2nd hot end heater....
6,00 € -
![[S] Dual extrusion upgrade Chimera Plus for Scalar S](http://3dmodularsystems.com/2722-small_default/-s-dual-extrusion-upgrade-chimera-plus-for-scalar-s.jpg)
[S] Dual extrusion upgrade Chimera Plus for Scalar S
Dual extrusion upgrade kit Two inputs, two outputs. The classic...
149,90 € -
![[S] Enclosure with air filtration system for Scalar S](http://3dmodularsystems.com/2699-small_default/-s-enclosure-with-air-filtration-system-for-scalar-s.jpg)
[S] Enclosure with air filtration system for Scalar S
Modular enclosure for 3D Scalar S 3D printer The enclosure is installed...
249,00 € -
![[XLP] Enclosure with air filtration system for Scalar XL Premium](http://3dmodularsystems.com/2627-small_default/-xlp-enclosure-with-air-filtration-system-for-scalar-xl-premium.jpg)
[XLP] Enclosure with air filtration system for Scalar XL Premium
Modular enclosure for 3D Scalar XL premium 3D printer The enclosure is...
349,00 € -
chainable RGB led WS2812
Programmable and chainable RGBW LED module (same model used on Neopixel)...
1,20 € -
PLA Electronic box for MKS GEN 1.4 / MKS GEN L
PLA electronic enclosure for MKS GEN 1.4 / MKS GEN-L boards The...
25,00 €
heatbeds for small print beds
Small There are 8 products.
Top aluminium plate for Scalar S 3D...
1 aluminum plates 3mm thick Laser cut 1 top plate 220x220x3mm with 4 holes in the corners for screws
23,40 €In StockBottom aluminium plate for Scalar S 3D...
1 aluminum plates 2mm thick Laser cut 1 top plate 220x220x2mm with 4 holes in the corners for screws 4 central holes for holding system
20,00 €In Stock[135°C] Silicone heater 250W 220V...
Large silicone heater for RepRap 3D printers Material: Silicone Size: 190x190mm Power: 250W Input Voltage: 220V Power supply cable length: 1 metre Back Tape: 3M Thermal fuse set at 140°C
48,90 €In StockPack heatbed for Scalar S 3D printer...
Heatbed Pack for Scalar S 3D printer Contains: 2 aluminum plates laser cut with fixation holes (1 top plate 3mm thick, 1 bottom plate 2mm thick) 1 silicone heatter (250W-220V) 1 thermistor 1 static relay + Wires Free: 1 set of nuts and bolts: 4 springs 4 conic head screws 4 nuts for conic screws 4 M6x12mm screws 4 M3 washers 4 nylstop nuts
98,50 €In StockScalar S Upgrade - Bottom aluminium plate...
1 aluminum plates 2mm thick Laser cut 1 top plate 220x220x2mm with 12 holes in the corners for screws 12 central holes for holding system
25,00 €In StockScalar S Upgrade - Heatbed 220V 250W
Upgrade kit for Scalar S Heat bed This kit contains: 1 Silicone plate, 250W, 220V with power plug (EU type) 1 static relay with a plastic casing 1 temperature sensor (thermistor) 1x 20cm ground wire
60,80 €In StockM4x20mm cone head screw White zinc steel
M4x20mm screw White zinc steel Full thread Din 965 M4x20mm cone head Pozidrive
0,14 €In Stock[95°C] Silicone heater 250W 220V 190x190mm...
Large silicone heater for RepRap 3D printers MAX 95°C (Thermal fuse set at 100°C) Material: Silicone Size: 190x190mm Power: 250W Input Voltage: 220V Power supply cable length: 1 metre Back Tape: 3M
29,00 €In Stock
![[95°C] Silicone heater 250W 220V 190x190mm](http://3dmodularsystems.com/2301-home_default/-95c-silicone-heater-250w-220v-190x190mm-for-scalar-s.jpg "[95°C] Silicone heater 250W 220V 190x190mm")