Scalar S There are 17 products.

• 

  Quick view

  70,87 € In Stock

  Dual Extrusion upgrade kit (Beta) for...

  This kit allows to convert your Scalar 3D printer or reprap 3d printer into a low cost Dual extrusion system. This system is based on a Y convector plastic part that allows to use 1 single hot end and 2 separate extruders. Features: Low congestion Lightweight bowden system Single hot end, multi extrusder system

  70,87 €

  Add to cart More

  In Stock

  Add to Compare
• 

  Quick view

  60,00 € Available under 1-2weeks

  Scalar S Upgrade - Dual Drive System kit

  Key features: Dual Drive System The bed will have 2 driving points on the sides of the bed instead of only 1 in the middle of it. Linear motion on 2020 aluminum extrusions Increases: The maximum payload (max weight of heatbed) Print quality Bed stabilityNo firmware change

  60,00 €

  Add to cart More

  Available under 1-2weeks

  Add to Compare
• 

  Quick view

  25,00 € In Stock

  Scalar S Upgrade - Bottom aluminium plate...

  1 aluminum plates 2mm thick Laser cut 1 top plate 220x220x2mm with 12 holes in the corners for screws 12 central holes for holding system

  25,00 €

  Add to cart More

  In Stock

  Add to Compare
• 

  Quick view

  60,80 € In Stock

  Scalar S Upgrade - Heatbed 220V 250W

  Upgrade kit for Scalar S Heat bed This kit contains: 1 Silicone plate, 250W, 220V with power plug (EU type) 1 static relay with a plastic casing 1 temperature sensor (thermistor) 1x 20cm ground wire

  60,80 €

  Add to cart More

  In Stock

  Add to Compare
• 

  Quick view

  49,00 € In Stock

  Upgrade Scalar S - Tiges trapézoïdales (kit)

  49,00 €

  Add to cart More

  In Stock

  Add to Compare
• 

  Quick view

  10,00 € In Stock

  Runout sensor module for reprap 3D printers

  Sensor capable of detecting when you are running out of filaments Allows the firmware of your 3D printer to trigger the change filament routine Allows to use the leftover of your filament for printing your things Compatible with RAMPS 1.4 boards and equivalent Compatible with both 1.75mm or 3mm filaments depending on the version selected

  10,00 €

  Add to cart More

  In Stock

  Add to Compare
• 

  Quick view

  47,65 € In Stock

  BLTouch (Antclab) Geniun auto bed leveling...

  Geniun Antclab BLTouch Auto bed leveling probe  Work under 5V Compatible with RAMPS 1.4 board Can sens any build surface Cable length: 20cm, may require extender wires

  47,65 €

  Add to cart More

  In Stock

  Add to Compare
• 

  Quick view

  20,00 € In Stock

  PS_ON Kit - auto power off your reprap 3D...

  Parts for automatic power off of your reprap 3D printer. It supports PS_ON feature available on Marlin Firmware.

  20,00 €

  Add to cart More

  In Stock

  Add to Compare
• 

  Quick view

  75,10 € In Stock

  TFT 2.8" Touch screen for 3D printer

  TFT 2.8" Touch screen compatible with Ramps 1.4 and MKS BASE Touch Screen SD card support USB key support Can be connected to a backup UPS Allows to resume print from power shortage Allows filament change during print

  75,10 €

  Add to cart More

  In Stock

  Add to Compare
• 

  Quick view

  75,10 € In Stock

  Sale!

  32Bits 100Mhz Re-Arm Controler for Scalar...

  RE-ARM is a 100Mhz, 32-bit ARM controller with the popular Arduino MEGA footprint. It's a plug-in replacement for the Arduino Mega in your RAMPS setup for a quick and easy upgrade to 32-bit goodness. It runs the awesome Smoothieware firmware by Arthur Wolf.

  75,10 €

  Add to cart More

  In Stock

  Add to Compare
• 

  Quick view

  95,20 € In Stock

  Sale!

  32Bits 100Mhz Re-Arm Controler + GLCD Full...

  RE-ARM is a 100Mhz, 32-bit ARM controller with the popular Arduino MEGA footprint. It's a plug-in replacement for the Arduino Mega in your RAMPS setup for a quick and easy upgrade to 32-bit goodness. It runs the awesome Smoothieware firmware by Arthur Wolf.

  95,20 €

  Add to cart More

  In Stock

  Add to Compare
• 

  Quick view

  169,50 € In Stock

  3Dtox the 3D printer air purifier

  Easy to install compatible with most FDM 3D printers Pre-assembled kit, ready to work within 10 minutes

  169,50 €

  Add to cart More

  In Stock

  Add to Compare