No products
Prices are tax included
New products
-
Bonwden connector for 3mm filament compatible with Titan extruder
Bonwden connector for Titan extruder Compatible with 6mm OD tubes for...
5,00 € -
Bowden Adapator / connector for 3mm filament
Bowden connector for E3D Titan extruder 3mm Compatible with 3mm...
8,28 € -
Bonwden connector for 1.75mm filament compatible with Titan and Bondtech BMG extruder
Bonwden connector for Titan extruder and Bondtech BMG Compatible with...
5,00 € -
Genuine E3D Titan Extruder
Precise and powerful extruder Increased resolution, thanks to it's gear...
63,90 € -
Nema 17 (42HM48), 400 steps / turn, 0.9° / step, Stepper motor for 3D printer
1 NEMA17 stepper motors compatible with Scalar 3D printers. Powerful,...
24,50 € -
MKS Tl-Smoother (Stepstick Protector) pour imprimante 3D reprap
MKS TL-Smoother Allows to smooth out the current on your Nema stepper...
2,80 €
Arduino There are 20 products.
RGB 3 Color LED, 5mm, Module For Arduino...
This is RGB 3 colors LED module for Arduino RGB signal output 3 color: Red, green, blue Input voltage: 5V Power: 5mW 5mm LED Compatible with Arduino DIY project
1,50 €In StockArduino Mega 2560 r3
Arduino Mega 2560 r3 controler board Microcontroleur Atmega 2560 Flash Memory: 256K SRAM: 8K EEPROM: 4K Frequency: 16 Mhz
17,53 €In StockMQ2 gaz sensor module for arduino
Gaz detector module compatible with arduino boards Input :5V Analog output TTL digital input Power: 800mw while heating Detection: smoke, Hydrogen, alcohol, methane, propane, i-buane, LPG
3,60 €Out of stockMicro Switch / Key module for Arduino
Micro switch / Key module for Arduino Max voltage: 12V Max current: 50mA Contact resistance: 50mΩ Insulation resistance: 100MΩ
1,20 €In StockArduino Yellow key module
Key module for Arduino Yellow Cap Input voltage: 3.3 - 5V Output: Digital Level (press low, release High) Compatible platform: Arduino, ARM, Raspberry pi, micro controlers
1,25 €In StockArduino Nano IO Expansion Board / Shield
Arduino Nano Expansion Board / Shield AREF Output: 3.3V Expand all 6 PWM pins Expans I2C pins Compatible only with Arduino NANO Expand DC power interface Available pins: +3.3V, +5V, GND, I2C, RX/TX, All other IOs
3,22 €In StockDRV8825/A4988 Stepper motor driver control...
Expansion board for Stepper Drivers Compatible with : DRV8825, A4988 Switch for micro stepping configuration power supply pins : +5V / +12V /+24V Control pins: Enable, Direction, Step Compatible with Arduino, Raspberry Pi, Ramps 1.4, ARM, etc....
4,92 €In Stock128X64 OLED Display module for Arduino...
0.96" OLED display for Arduino application Resolution: 128X64 Ultra low power: 0.08W Input voltage: 3-5VDC Color: Blue/White
6,50 €In Stock20Cm 3 pins jumper wire Dupont cable...
3Pin Dupont wire for all your Arduino, raspberry pi, etc... projects 3 Pins Dupont 3 Pins connector, 2.54mm Female-Female 20cm
0,45 €In Stock20Cm 4 pins jumper wire Dupont cable...
4Pin Dupont wire for all your Arduino, raspberry pi, etc... projects 4 Pins Dupont 4 Pins connector, 2.54mm Female-Female 20cm
0,55 €In Stock20Cm 2 pins jumper wire Dupont cable...
2Pin Dupont wire for all your Arduino, raspberry pi, etc... projects 2 Pins Dupont 2 Pins connector, 2.54mm Female-Female 20cm
0,36 €In Stock
