[RPI] LCD Display 3.5" Waveshare compatible RPI B+/2B/3B/3B+ IPS

ECO-WAVESHARE-3.5INCH-IPS

New product

  • LCD Display IPS WaveShare compatible with Raspeberry pi B+/2B/3B/3B+
  • Resolution 480x320
  • Resitive Touch screen
  • Can be plugged directly on Raspberry pi GPIO

More details

In Stock

26,91 € tax incl.

-10%

29,90 € tax incl.

Including 0,10 € for ecotax
(not impacted by the discount)

More info

Originale Waveshare Display

  • Resolution: 480x320
  • Resistive touchscreen
  • Supports any Raspberry pi version
  • Drivers are provided (compatible with Raspbian, Ubunti Kali)
  • Supports FBCP drivers,Allows to use the screen in DUal-display mode
  • IPS Technology, High quality display with a wide range view.
  • Same size as Raspberry Pi

Key parameters:

LCD type: IPS

LCD Interface: SPI

Touch screen type: Resistive

Touch screen controler: XPT2046

Colors: 65536

Backlight: LED

Resolution: 480x320 (Pixels)

Aspect ratio: 8:5

Interface:

PIN NO.SYMBOLeDESCRIPTION
1, 173.3VInput voltage
2, 45VInput voltage
3, 5, 7, 8, 10, 12, 13, 15, 16NCNC
6, 9, 14, 20, 25GNDGround
11TP_IRQTouch screen interrupt input, Low level when touch press is detected
18LCD_RSInstruction/Data Register select
19LCD_SI / TP_SISPI LCD/Touch Panel input data
21TP_SOTouch screen  SPI output data
22RSTReset
23LCD_SCK / TP_SCKSPI clock of LCD/Touch Panel
24LCD_CSLCD chip selection, low level active
26TP_CSTouch Panel chip selection, low level active

Size:

Dimensions de l'écran LCD Waveshare 3.5 Pouces compatible Raspberry pi

Additional Ressources:

Wiki : www.waveshare.com/wiki/3.5inch_RPi_LCD_(B)

FAQ:

Why the LCD doesn't work with my Raspbian?

To use the LCD with the Raspberry Pi official image, driver should be installed first. Please refer to the user manual.

However, for the first testing, you may want to use our provided image directly.

Why the LCD still doesn't work with the Waveshare provided image?

Make sure the hardware connection is correct and connects fine.
Make sure the image in TF card is burnt correctly.
The PWR will keep on and the ACT will keep blinking when the Raspberry Pi starts up successfully, in case both of the two LEDs keep on, it is possible that the image was burnt incorrectly OR the TF card was in bad contact.

Which power supply should I use?

It is recommended to use a 5V/3A power adapter for the Raspberry Pi other than USB connection, otherwise the Pi may failed to start up because the PC's USB port might have not enough power.
For large size LCDs, say, 10inch diagonal or more, another stand-alone power adapter is also required to provide power to the LCD.

If the LCD is intended to play videos, please choose the one with HDMI display interface for better experience.

Reviews

No customer reviews for the moment.

Write a review

[RPI] LCD Display 3.5" Waveshare compatible RPI B+/2B/3B/3B+ IPS

[RPI] LCD Display 3.5" Waveshare compatible RPI B+/2B/3B/3B+ IPS

  • LCD Display IPS WaveShare compatible with Raspeberry pi B+/2B/3B/3B+
  • Resolution 480x320
  • Resitive Touch screen
  • Can be plugged directly on Raspberry pi GPIO

Accessories

Customers who bought this product also bought: