MKS-Gen 1.4 Controler board for 3d printer

ECO-MKS-GEN14

New product

MKS GEN 1.4 3D printer controler board

  • Atmega 2560 microcontroler
  • Integrated Ramps 1.4 board
  • has similar Aux outputs as Ramps 1.4
  • Compatible with all standard Stepper motor drivers for 3D printers
  • Compact form factor
  • Ideal replacement for Arduino 2560 + Ramps 1.4

More details

In Stock

39,90 € tax incl.

Including 0,03 € for ecotax

Data sheet

USB printingYes
CPU typeAtmega 2560 - r3, 16Mhz, 8-Bit , 256 Kbytes program memory, 4KBytes EEPROM memory, 8KBytes SRAM
ChipsetAtmega2560
Speed16Mhz

More info

this board combines both Arduino 2560 and Ramps 1.4

It can be used on any DIY project.

Compatible with arduino IDE

This boards also exposes +5 and +12V output pins

Caracteristics:

  • microcontroleur: ATmega2560
  • Input voltage: 12-24V
  • Available Auxiliary output voltage: 3x5V, 3x12V
  • Aux ports: Aux 1, 2 , 3
  • Flash memory: 256K
  • SRAM: 8K
  • EEPROM 4K
  • Speed: 16Mhz
  • Size: 143*84mm
  • Extruder count: 2
  • Fan outputs: 1
  • Compatible with thermistor modules AD597 / PT100 (requires additional board)
  • End stop inputs: 6
  • Stepper motor supported: 5
  • PWM high power outputs: 4 (bed, extrudeur 0 et 1, Fans)
  • Optimized heat sink dissipation (4 PCB layers)
  • Protection against short circuit - Resetable fuse 
  • Compatible with wifi/bluetooth modules
  • 5 Generic slots for standard Stepper motor drivers (A4988, DRV8825, TMC2100, TMC2208, TMC2130,LV8729 etc...)
  • Compatible with most common displays (LCD2004, LCD12864, MKS TFT, OLED etc...
  • Compatible with all slicers: Simplify 3D, kisslicer, Cura, Repetier, IceSL, Mattercontrol, etc...
  • Compatible with SD card (integrated with LCD displays)
  • directly compatible with MKS TFT 2.8 et MKS TFT 3.2 touch displays

Max currents:

  • Input power: 15A max
  • Heater cartridges: 10A max
  • Heat bed: 13A max
  • stepper motor driver: 2A max
  • heat bed with mosfet: 25A max
  • Hot end with mosfet; 4A max
  • fans: 10A max

Stepper driver micro stepping configuration

A4988

MS1

MS2

MS3

Pas

0

0

0

pas plein

1

0

0

1/2 pas

0

1

0

1/4 pas

1

1

0

1/8 pas

1

1

1

1/16 pas

DRV8825

MS1

MS2

MS3

pas

0

0

0

plein pas

1

0

0

1/2 pas

0

1

0

1/4 pas

1

1

0

1/8 pas

0

0

1

1/16 pas

1

0

1

1/32 pas

0

1

1

1/32 pas

1

1

1

1/32 pas

Displays

MKS Gen 1.4 + LCD 2004

2004.jpg

CAUTION!

Depending on the display model you are using, the back connexion might need to be inverted

If you are using special MKS LCD2004 displays , they will be compatible without any changes

In case of RepRapDiscount LCD2004 displays you will need to invert the DB10 connector at the back of the display

Connexion with MKS LCD2004

Connexion with standard ReprapDiscoun LCD2004 displays!

MKS Gen 1.4 + GLCD 12864

2004.jpg

MKS Gen 1.4 + MKS TFT 2.8 / 3.2

I/Os + wiring diagram

MKSGen 1.4 Schéma de câblage

MKSGen 1.4 pinout

MKSGen 1.4 implantation

Security notice

Any wiring process requires attention and very basic logic. any short circuit or wrong use of the board I/Os can generate fire hazard.

WARNING: make sure to check max power requirements before using any devices on any I/Os.

Warning: Make sure to check wiring polarity in order to prevent from short circuit or any electrical damages

Firmware installation

please check Datasheet for firmware installation instructions

Scalar 3D printer compatible box for MKS GEN Controler boards

Boitier électronique Scalar pour carte MKS GEN

Thingiverse

Datasheet

Github

Reviews

No customer reviews for the moment.

Write a review

MKS-Gen 1.4 Controler board for 3d printer

MKS-Gen 1.4 Controler board for 3d printer

MKS GEN 1.4 3D printer controler board

  • Atmega 2560 microcontroler
  • Integrated Ramps 1.4 board
  • has similar Aux outputs as Ramps 1.4
  • Compatible with all standard Stepper motor drivers for 3D printers
  • Compact form factor
  • Ideal replacement for Arduino 2560 + Ramps 1.4

Accessories

Customers who bought this product also bought:

Download