MKS-Gen_L Controler board for 3d printer

ECO-MKS-GEN_L

New product

MKS GEN 1.4 3D printer controler board

  • Atmega 2560 microcontroler
  • Integrated Ramps 1.4 board
  • has similar Aux outputs as Ramps 1.4
  • Compatible with all standard Stepper motor drivers for 3D printers
  • Compact form factor
  • Ideal replacement for Arduino 2560 + Ramps 1.4
  • Supports 12/24VDC input
  • Optimized MOSFET heat dissipation

More details

In Stock

Warning: Last items in stock!

32,50 € tax incl.

Including 0,03 € for ecotax

Data sheet

USB printingYes
CPU typeAtmega 2560 - r3, 16Mhz, 8-Bit , 256 Kbytes program memory, 4KBytes EEPROM memory, 8KBytes SRAM
ChipsetAtmega2560
Speed16Mhz

More info

this board combines both Arduino 2560 and Ramps 1.4

It can be used on any DIY project.

Compatible with arduino IDE

This boards also exposes +5 and +12V output pins

Caracteristics:

  • microcontroleur: ATmega2560
  • Input voltage: 12-24V
  • Available Auxiliary output voltage: 2x5V, 1x12V
  • Aux ports: Aux 1, 2 , 3
  • Flash memory: 256K
  • SRAM: 8K
  • EEPROM 4K
  • Speed: 16Mhz
  • Size: 110*84mm
  • Extruder count: 2
  • Fan outputs: 1
  • Compatible with thermistor modules AD597 / PT100 (requires additional board)
  • End stop inputs: 6
  • Stepper motor supported: 5
  • PWM high power outputs: 4 (bed, extrudeur 0 et 1, Fans)
  • Optimized heat sink dissipation (4 PCB layers)
  • Protection against short circuit - Resetable fuse 
  • 5 Generic slots for standard Stepper motor drivers (A4988, DRV8825, TMC2100, TMC2208, TMC2130,LV8729 etc...)
  • Compatible with most common displays (LCD2004, LCD12864, MKS TFT, OLED etc...
  • Compatible with all slicers: Simplify 3D, kisslicer, Cura, Repetier, IceSL, Mattercontrol, etc...
  • Compatible with SD card (integrated with LCD displays)
  • directly compatible with MKS TFT 2.8 et MKS TFT 3.2 touch displays

Max currents:

  • Input power: 15A max
  • Heater cartridges: 10A max
  • Heat bed: 13A max
  • stepper motor driver: 2A max
  • heat bed with mosfet: 25A max
  • Hot end with mosfet; 4A max
  • fans: 10A max

Stepper driver micro stepping configuration


Displays

MKS Gen_L + LCD 2004

2004.jpg

CAUTION!

Depending on the display model you are using, the back connexion might need to be inverted

If you are using special MKS LCD2004 displays , they will be compatible without any changes

In case of RepRapDiscount LCD2004 displays you will need to invert the DB10 connector at the back of the display

Connexion with MKS LCD2004

Connexion with standard ReprapDiscoun LCD2004 displays!

MKS Gen_L + GLCD 12864

2004.jpg

MKS Gen_L + MKS TFT 2.8 / 3.2

I/Os + wiring diagram

MKS-Gen_L Wiring schematic

MKS-Gen_L pinout

MKS-Gen_L implantation

Security notice

Any wiring process requires attention and very basic logic. any short circuit or wrong use of the board I/Os can generate fire hazard.

WARNING: make sure to check max power requirements before using any devices on any I/Os.

Warning: Make sure to check wiring polarity in order to prevent from short circuit or any electrical damages

Scalar 3D printer compatible box for MKS GEN Controler boards

Boitier électronique Scalar pour carte MKS GEN

Thingiverse

Firmware installation

Requirements:

Please check Datasheet for any Firmware installation instructions

Datasheet

GitHub

Reviews

No customer reviews for the moment.

Write a review

MKS-Gen_L Controler board for 3d printer

MKS-Gen_L Controler board for 3d printer

MKS GEN 1.4 3D printer controler board

  • Atmega 2560 microcontroler
  • Integrated Ramps 1.4 board
  • has similar Aux outputs as Ramps 1.4
  • Compatible with all standard Stepper motor drivers for 3D printers
  • Compact form factor
  • Ideal replacement for Arduino 2560 + Ramps 1.4
  • Supports 12/24VDC input
  • Optimized MOSFET heat dissipation

Accessories

Customers who bought this product also bought:

Download